/* $NetBSD: if_cuereg.h,v 1.22.2.1 2019/09/01 13:00:37 martin Exp $ */ /* * Copyright (c) 1997, 1998, 1999, 2000 * Bill Paul . All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. All advertising materials mentioning features or use of this software * must display the following acknowledgement: * This product includes software developed by Bill Paul. * 4. Neither the name of the author nor the names of any co-contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF * THE POSSIBILITY OF SUCH DAMAGE. * * $FreeBSD: src/sys/dev/usb/if_cuereg.h,v 1.3 2000/01/16 22:45:06 wpaul Exp $ */ /* * Definitions for the CATC Netmate II USB to ethernet controller. */ #include /* * Vendor specific control commands. */ #define CUE_CMD_READSRAM 0xF1 #define CUE_CMD_GET_MACADDR 0xF2 #define CUE_CMD_RESET 0xF4 #define CUE_CMD_WRITEREG 0xFA #define CUE_CMD_READREG 0xFB #define CUE_CMD_WRITESRAM 0xFC /* * Internal registers */ #define CUE_TX_BUFCNT 0x20 #define CUE_RX_BUFCNT 0x21 #define CUE_ADVANCED_OPMODES 0x22 #define CUE_TX_BUFPKTS 0x23 #define CUE_RX_BUFPKTS 0x24 #define CUE_RX_MAXCHAIN 0x25 #define CUE_ETHCTL 0x60 #define CUE_ETHSTS 0x61 #define CUE_PAR5 0x62 #define CUE_PAR4 0x63 #define CUE_PAR3 0x64 #define CUE_PAR2 0x65 #define CUE_PAR1 0x66 #define CUE_PAR0 0x67 /* Error counters, all 16 bits wide. */ #define CUE_TX_SINGLECOLL 0x69 #define CUE_TX_MULTICOLL 0x6B #define CUE_TX_EXCESSCOLL 0x6D #define CUE_RX_FRAMEERR 0x6F #define CUE_LEDCTL 0x81 /* Advenced operating mode register */ #define CUE_AOP_SRAMWAITS 0x03 #define CUE_AOP_EMBED_RXLEN 0x08 #define CUE_AOP_RXCOMBINE 0x10 #define CUE_AOP_TXCOMBINE 0x20 #define CUE_AOP_EVEN_PKT_READS 0x40 #define CUE_AOP_LOOPBK 0x80 /* Ethernet control register */ #define CUE_ETHCTL_RX_ON 0x01 #define CUE_ETHCTL_LINK_POLARITY 0x02 #define CUE_ETHCTL_LINK_FORCE_OK 0x04 #define CUE_ETHCTL_MCAST_ON 0x08 #define CUE_ETHCTL_PROMISC 0x10 /* Ethernet status register */ #define CUE_ETHSTS_NO_CARRIER 0x01 #define CUE_ETHSTS_LATECOLL 0x02 #define CUE_ETHSTS_EXCESSCOLL 0x04 #define CUE_ETHSTS_TXBUF_AVAIL 0x08 #define CUE_ETHSTS_BAD_POLARITY 0x10 #define CUE_ETHSTS_LINK_OK 0x20 /* LED control register */ #define CUE_LEDCTL_BLINK_1X 0x00 #define CUE_LEDCTL_BLINK_2X 0x01 #define CUE_LEDCTL_BLINK_QUARTER_ON 0x02 #define CUE_LEDCTL_BLINK_QUARTER_OFF 0x03 #define CUE_LEDCTL_OFF 0x04 #define CUE_LEDCTL_FOLLOW_LINK 0x08 /* * Address in ASIC's internal SRAM where the * multicast hash table lives. The table is 64 bytes long, * giving us a 512-bit table. We have to set the bit that * corresponds to the broadcast address in order to enable * reception of broadcast frames. */ #define CUE_MCAST_TABLE_ADDR 0xFA80 #define CUE_MCAST_TABLE_LEN 64 #define CUE_CTL_READ 0x01 #define CUE_CTL_WRITE 0x02